Mipro MA-708 User's Guide download pdf (Page 9)

3. Press & hold

"SCAN" button

for 1 second

4. Existing channel

blinks

AUTOMATIC “TRANSMITTER” SYNC

1. POWER on transmitter (ensure fresh batteries are properly installed with the correct

polarity). Replace transmitter battery when LED glows red during powered-on. (glows red

= low battery)

2. Locate and bring an ACT transmitter *infrared (IR) port within 30cm (12-inch) of

receiver's ACT button.

3. Press and release “ACT” button to synchronize transmitter and receiver frequencies.

4. When the frequencies are synchronized successfully the receiver channel stops flashing

and the RF meter is fully lit, the microphone is now ready for use.

NOTE: The transmitter infrared IR port is normally located by a round-shaped red color

spot.

SCAN

ACT SENSITIVITY

CHANNEL NOISE

SCAN

ACT SENSITIVITY

CHANNEL NOISE

AUTOMATIC “RECEIVER” FREQUENCY SELECTION

1. POWER "ON" the portable PA

2. POWER on receiver by turning "VOLUME" knob.

POWER

VOLUME

WIRELESS INTERLINKING TRANSMITTER AND RECEIVER MODULES

Users have options to add a single MTM-90/MTM-92 wireless transmitter or MRM-72/

MRM-72B receiver module in this slot.

The purpose of MTM-90/MTM-92 wireless interlinking transmitter is to interlink multiple

MIPRO MA-708 portables wirelessly to greatly extend the transmission range and expand

coverage.

INSTALLATION OF MTM-90/MTM-92 WIRELESS INTERLINKING TRANSMITTER

! Using a Phillips-head screwdriver (not supplied) remove the screws to remove protection

cover panel.

! Gently insert the transmitter module into the slot. Make sure the back edge connector is

aligned and firmly connected.

! Tighten up the screws.

OPERATION INSTRUCTIONS OF MTM-90/MTM-92 WIRELESS INTERLINKING

TRANSMITTER

SCAN

ACT SENSITIVITY

CHANNEL

NOISE

VOLUME

Power Switch/Volume Knob

Channel LED Display

MT-90/MT-92 transmitter module

Channel-Selecting Button

Power Indicator

Level Limiter Indicator

Bodypack Transmitter Storage

C6C5

MRM-72/MRM-72B receiver module consists of 2 MRM-70/MRM-70B receiver modules

side-by-side.

MTM-90/MTM-92 Wireless Interlinking Transmitter

1. To select a channel one at a time: Press and hold the Channel-Selecting button for

around 2 seconds and release when channel LED display starts flashing. Press and

release button once to move to the next available channel. If button is not pressed again

when Channel LED flashes 6 times, the channel appearing in Channel Display is

automatically saved and set.

2. To select channel continuously: Press and hold the Channel-Selecting button for

around 2 seconds until channel LED display starts flashing. Press and hold same

button will automatically advance channel continuously until stopped. There are a total

of 16 preset channels. If button is not pressed again when Channel LED flashes 6 times,

the channel appearing in Channel Display is automatically saved and set.

The Level Limiter Indicator will not be lit under normal audio volume. If the au dio input

exceeds the set limitations, volume restriction control will activate and the indicator will

lit. Adjust volumes to an acceptable levels.

Power On/Off:

Select Channels:

Turn the transmitter power/volume switch to ON by rotating the knob clockwise. When

ON, the power indicator and Channel LED Display will be lit. Rotate volume knob

clockwise to adjust the desired volume. Rotate same volume knob counterclockwise to

power OFF the transmitter.

RF RF

AFAF

VOLUMEVOLUME

MRM-70 -RMRM-70 -R

5. Press & release

"SCAN" button

6. New

interference-free

channel appears

SCAN

ACT SENSITIVITY

CHANNEL NOISE

SCAN

ACT SENSITIVITY

CHANNEL NOISE

RF RF

AF AF

VOLUME VOLUME

MRM-70 -R MRM-70 -R

PORTABLE WIRELESS PA SYSTEM PORTABLE WIRELESS PA SYSTEM

C1 C2 C4 C3

SET-UP RECEIVER AND TRANSMITTER FREQUENICES

30c

m (1

SCAN

ACT SENSITIVITY

CHANNEL

NOISE

VOLUME

1 2 3 4 5 6 7 8 9 10 11 12 13

Comments to this Manuals

No comments

Mipro MA-708 User's Guide Page 9

Comments to this Manuals